msi GeForce RTX 4060 Ti Graphics Card

كرت قوي يشغل اقوى الالعاب بدون اي مشاكل والتبريد ممتازومايصرف طاقة

I upgraded from the 3060 ti to this new card. It is working flawlessly and performs great for 1080p gaming

For the people with constraints on the power supply, this RTX 4060 Ti (16GB) provides the best performance. Most people may choose RTX 4070 for even better performance, or RTX 3060/4060 for better value. However, in my case, my HP Envy desktop came with 310W HP-customized PSU, and the most powerful PSU I could upgrade to was 500W as the motherboard and the chassis don’t take standard PSU. RTX 4070 is recommended to have 650W PSU, while 4060 Ti is recommended to have 500-550W PSU, so RTX 4060Ti is the most powerful candidate that I could try.
The benchmark scores didn’t disappoint me. I got 26541 in Passmark. As comparison, the average score of 4060 Ti is 22565, average RTX 4070 is 26841, average RTX 3080 is 25354. The OC frequency I observed in Afterburner is 2775 MHz (much higher than the 2626 MHz claimed in the title), and it stays at this frequency very stably for long time. The power consumption during gaming also stays at 160-165W very stably, and it could go lower if you turn on V-Sync and set refresh rate to 60fps. In idle mode, the power consumption is between 10-13W and the fans stop spinning.
As a conclusion, I believe the higher OC frequency brings the Passmark score to be on par with RTX 4070 and even slightly exceeds RTX 3080, although I guess in the real games, probably it is still going to be a little behind those 70/80-class cards, but not too much.

Update Jan’24: I’am getting 90fps on the highest quality settings on 4K resolution of Baldur’s Gate 3 (with DLSS on). I tried both dx11 and Vulcan, similar FPS but with VSync the Vulkan gets lower GPU load (60%) on 60 Hz, which reduces the power consumption and fan noise significantly. Very impressive! By the way, sometimes the GPU Memory usage reaches 9GB+ on Volkan.
On Total War Warhammer II 4K resolution benchmarks, I got 60.7 fps on High settings and 50.8 fps on Ultra settings.
Update Sept. ’24: I have tested many games so far: FF7 Remake, FF15, FF16, Horizon Zero Dawn/Forbidden West, Monster Hunter Rise/World, The Outer World, Mass Effect, Cyberpunk, Civ 6 etc. After careful configuration of DLSS, I could consistently get 60+fps at 4K resolution with the highest quality settings on most of these games! The only exceptions are the Total War series (which doesn’t support DLSS at all so I had to reduce the quality setting) and Cyberpunk 2077 (which I still got 50+ fps, after turning off certain effects like film grains etc. and choose DLSS Ultra performance).
Also I consistently see more than 8GB graphics memory usage — and it could be up to 14GB on Horizon Zero Dawn!
Considering the highest memory usage (more than the 12GB offered by 4070) and the lower power consumption, I still believe this is the best choice for power limited users like me.

Everything came on time, without any problems, the video card is completely as described by the seller, RTX 4060 ti 16gb.

For those who want to order goods to Georgia: Keep in mind that I paid an additional 18 percent of the price for this item, this is a Georgia rule, the seller had nothing to do with it.

I am using the RTX4060 TI 16GB in an Intel NUC9 (NUC9VXQNB) to edit videos with DaVinci Resolve. The Intel NUC is a small formfactor PC that allows GPUs with a maximum length of 20cm – i.e. the choice of GPUs that fit inside is severely limited.

After increasing the resolution/bitrate of my video clips, my computer and my old GPU (RTX 3060 12GB) were struggling playing back videos fluently and I decided to upgrade. The goal was to find a GPU that was faster and had more GPU memory (DaVinci crashes if GPU memory gets low).

Conventional wisdom in the computer hardware newsgroups is that the RTX4060 TI is not a good upgrade from an RTX 3060 but I bit the bullet and ordered the card. For my use case (video editing), the new GPU is 12-34% faster than the old one.

In the tests mentioned below, I used high resolution video clips with roughly 200 Mb/s bitrate. Each clip was stabilized in real-time with Gyroflow and two LUTs were applied for color correction. Most of the clips had some form of light noise reduction and some clips had heavy (spatial + temporal) noise reduction applied. Videos exported in 1080P used a 1080P timeline and videos exported in 4K were using a 4K timeline. My computer was running Windows 11 with the latest NVidia drivers.

A typical mix of video clips exported in 1080P:
RTX3060: 6:45min RTX4060TI: 4:58min (26% speedup)

A typical mix of video clips exported in 4K:
RTX3060: 12:35min RTX4060TI: 11:01min (12% speedup)

Video clips with heavy noise reduction exported in 1080P:
RTX3060: 13:34min RTX4060TI: 8:50min (34% speedup)

Video clips with heavy noise reduction exported in 4K:
RTX3060: RTX4060TI: no crash/video got exported.

In summary: the speedup is not as much as I was hoping for but due to the space constraints of my Intel NUC, I decided to keep the card. Is this card worth the money? Probably not … but in my case it makes the video editing process more pleasant.

 This was a huge upgrade for me from my 6gb graphics card on my laptop. I can run games at full ultra settings and see the beautiful visuals. I did see a couple negative things about this graphics card, not sure if they were all about this exact model.

I haven’t had any issues with the graphics card and I’m glad I chose this one. Its both small and efficient, holding 16 gigs of VRAM. The price compared to other graphics cards of the same 16gb is what also really convinced me to just buy this one.

Solid card. Runs quiet (when adjusted software) and has zero issues over heating. Quality product for the price point.